Install an Outlet in a Wall

So your home hasn’t got enough outlets? Why not add a few to make the room a little more convenient? In this article, you’ll learn how to add another outlet in an existing wall. These easy steps can be accomplished without damaging the portion of the wall that you see.

1. Turn Off the Power
As with any other electrical project, turn off the power to the circuit that you’ll be working on. To do this, use a tester or plug something into the outlet. Go to the breaker or fuse panel and turn the circuit off that feeds the outlet.

2. Before You Start
Before starting the project, face the wall that needs another outlet. Clear everything away from the wall that you’ll be working on. Locate the base trim and with a pencil, lightly mark the top edge of the base trim so that it leaves a mark on the drywall.

3. Remove the Base Trim
The first step is to remove the base trim. Use a razor knife to break loose any paint that may be attached where the wall and trim meet. Yours may not have this problem, but I’ve listed it just in the event you do. Use a putty knife to loosen the trim from the wall and then use a flat bar to remove the trim. Push the flat bar down between the wall and the trim. Pull away from the wall with the flat bar the entire length of the trim. Set the trim aside for now.

4. Cut the Drywall
Using a drywall saw, cut just below the pencil mark that you just marked on the wall. Be careful not to cut too deep and cut a wire hidden behind the drywall. Carefully pull the piece of cut drywall away from the wall. Set it aside so that you can reinstall it later.

5. Drill the Studs
Using a drill and a 3/4″ paddle bit, drill holes in the center of the 2×4’s, just above the plate. Do this from the existing outlet to the location where you’d like the new outlet.

6. Adding the Wire
Install 12-2 NM (Romex)through the holes that you drilled. Leave some slack at each end for adjustments later. If your box requires a Romex connector, add it now about six to seven inches from the end of the wire. Remove the lock nut for now. You will need it later.

7. Feeding Wire to the Existing Box
From the existing box, take the knockout out of the bottom of the box. Feed a fish tape or a scrap piece of wire through the hole until you see it in the opening that you cut below. Attach the Romex to it with electrical tape and pull it through the hole in the box. Attach the lock nut and secure it with a tap on a screwdriver.

8. Mark the New Outlet
Take a tape measure and measure the top of the existing outlet. Now mark the new outlet the same. Use a pencil and a level to align and mark the new cut-in box.

9. Install the Cut-in Box
Using the drywall saw, cut the drywall and remove the scrap. Knock the bottom knockout out of the cut-in box, so that you’ll be able to insert the wire. Now, install the box and tighten the side straps or add Madison straps to hold the box in place.

10. Feeding Wire to the Cut-in Box
Feed a fish tape or a scrap piece of wire through the hole until you see it in the opening that you cut below. Attach the Romex to it with electrical tape and pull it through the hole in the box. Attach the lock nut and secure it with a tap on a screwdriver. Your box may have its own wire strap. If so, tighten it once the wire is pulled at least six inches into the box.

11. Reinstall Drywall and Trim
Using drywall screw, reinstall the drywall piece that you earlier cut out. Reinstall the base trim and what do you know? The project is complete and you wouldn’t even know that anything had been done. Well, except for a little vacuuming that may need to be done.

12. Connect the New Outlet
Strip the outer coating from the Romex and strip the black and white wires about 3/4 inch. Bend a half moon and wrap the black wire clockwise around the brass colored screw. The white wire is next and it is attached similarly, only to the silver colored screw. The bare copper wire connects to the green screw. Tuck the wires into the box and screw the outlet into the box. Install the cover plate and you’re finished with this outlet.

13. Connect the Existing Outlet
The existing outlet will need a pigtail connection. This involves cutting scrap pieces of the three colored wires and attaching one end to the outlet and the other to the two pieces of Romex. Find out how to attach a pigtail. Attach wire nuts to connect the wires. Gently press the wires into the box and screw the outlet into the box. Install the outlet’s cover plates and you have finished the outlet installation.

14. Turn On the Power and Test
The final step is to turn the circuit back on and test the circuit. Be sure to try both the new and the old outlet. It is as easy and painless as that and you’ll have everyone wondering how you did it!

Leave a Reply